{"id":1897,"date":"2018-03-15T14:42:04","date_gmt":"2018-03-15T14:42:04","guid":{"rendered":"http:\/\/www.blog.exrockets.com\/blog\/?p=1897"},"modified":"2018-04-03T15:18:33","modified_gmt":"2018-04-03T15:18:33","slug":"making-platinum-foil-and-platinum-titanium-anodes-for-perchlorates-persulphates","status":"publish","type":"post","link":"http:\/\/www.blog.exrockets.com\/blog\/making-platinum-foil-and-platinum-titanium-anodes-for-perchlorates-persulphates\/","title":{"rendered":"MAKING PLATINUM FOIL AND PLATINUM-TITANIUM ANODES FOR PERCHLORATES \/ PERSULPHATES"},"content":{"rendered":"

\"\"<\/a><\/p>\n

Large area Platinum electrodes or catalysts are often needed if you are interested in chemistry and science. Unfortunately large area Platinum mesh or foil are extremely expensive for the corresponding weight, the same is valid as well for Pt coated materials, not to mention their higher wear and the fact that they simply don\u2019t work in some cases – for example anodes made from Platinum coated Titanium substrate are very popular but the actual Platinum that you purchase with it is very little and electro-coated Platinum wears much faster than rolled (forged) Platinum with highly compressed crystal surface structure.<\/p>\n

So for a while I\u2019ve been researching a technology and methods to make high quality Platinum anodes for chemistry (and other purposes). I was able to find very little practical information in the books and on the net. Thus I had to find for myself through trial and errors a lot of the little tricks that I\u2019ll be sharing further down.<\/p>\n

If you think this is something you would like to try, be advised that before you make your first platinum foil and anodes, you will need some equipment that you cannot buy but you have to build for yourself, or a friend who can do it for you on lathe and milling machine.<\/p>\n

Further you will need a small Oxy-MAPP\/Acetylene torch, please note that large torch is not going to work, a spot welder – something that you can build yourself as well or use a commercial one and of course some Platinum to work with. Add to that a lot of patience until you become comfortable with the process.<\/p>\n

STOCK MATERIAL<\/strong><\/h2>\n

PURE PLATINUM BAR<\/p>\n

\"\"<\/a><\/p>\n

To make Platinum foil you will need \u2026 well Platinum. The best material is to buy a pure 99.9% Platinum bar from somewhere (I purchased mine from E-bay, APMEX). You probably won\u2019t need more than 3gr Pt but it depends what you plan to do with the foil.\u00a0 I found out that one 5gr bar come cheaper than buying 3 x 1gr bars \u2013 so I took one 5gr bar.<\/p>\n

 <\/p>\n

SCRAP JEWELRY<\/p>\n

\"\"<\/a><\/p>\n

Another source of Platinum could be scrap metal from a jewelry shop \u2013 the picture below is me re-melting scrap Pt. However this is rarely pure Platinum and you have to make good calculations on how much pure platinum you are actually buying, it might come cheaper to simply purchase a pure Platinum bar on-line or elsewhere. Be advised that during the melting all non-noble metals will be oxidized and burnt away \u2013 so don\u2019t be surprised if after melting the material you have less than the starting weight. Sometimes in the jewelry Platinum there is Iridium present to alloy it, which is not advisable (see next paragraph).<\/p>\n

THERMOCOUPLES AND RELAYS<\/p>\n

The last common source of platinum that I have used is thermocouples and relays. These sometimes can be found on the \u201cblack\u201d market where defective thermocouples and relays are sold. Thermocouples contain Pt-Pd and relays Pt-Ir alloys. You should be well aware what you are buying and how much noble metal you are getting. Sometimes in the high-temperature thermocouples Palladium is replaced with alloys from non-noble metals. Although the Iridium and\u00a0Palladium can be used alloyed together with Platinum in 99% of the semi-amateur cases where Platinum foil or anodes are required, the Pt-Ir-Pd alloy is hard, more brittle and difficult to mill.<\/p>\n

MELTING<\/strong><\/h2>\n

Platinum has high melting point (1765*C) and simple propane or propane-oxy torch will not be sufficient. You need an oxy-MAPP or oxy-acetylene or other high temperature torch. Further you can\u2019t simply the big torch from the workshop, you need something smaller because you will blow away the Pt pieces and bits. In my case I am using a brazing oxy torch as the one on the picture bellow.<\/p>\n

Further you will need a crucible to melt the Platinum into. The cheapest option is a small quartz crucible. Those can be purchased on Internet extremely cheap.\u00a0 Although the quartz has lower melting point than platinum, it has very low thermal conductivity and only a thin layer under the platinum gets molten.<\/p>\n

\"\"<\/a>\u00a0\"\"<\/a><\/p>\n

Whatever gas you are using Platinum should not be melted in carbon rich media and you should always use an oxygen rich flame<\/span>. So if you are thinking about induction heating, then you will need a graphite crucible but this is no-go as I mentioned. The reason is because the carbon enters in the molten Platinum and resulted alloy is very brittle.<\/p>\n

When the Pt starts melting, the surface tension will form a drop.\u00a0 The drop will become bright white and you will think it fully molten \u2013 it is not. If you stop here, the resulting bit of Platinum is very brittle and will crack and shear very easy, you can\u2019t mill that material. My explanation (I am not a scientist and can\u2019t claim this to be true) is that at this point part of the crystal lattice is molten, but there still individual crystals in it. So you have to continue heating the drop of Pt until is fully melted<\/span>. But how you can know when to stop \u2013 you will notice that the more you heat it the brighter it becomes. At some point you will see a very noticeable decrease in the brightness<\/span> of the drop, at this point it will also lose the spherical and take a more flat shape<\/span> \u2013 now you can stop heating it. For this reason it is a good idea to direct the torch sideways so that the drop of platinum starts spinning in the quartz bead \u2013if there are remaining oxides as impurities you can see the accumulating at the top of the drop as separate raised \u00a0dome.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

Now we leave the platinum bit to cool down really well. During the melting process as I mentioned earlier, the Pt will form a bed of molten quartz in the crucible. That molten quartz acts as flux<\/span> and reacts with the oxides of the non-noble metals (if there were such) in the platinum, thus refining the Pt. Speaking of non-noble metals, by using oxygen rich flame and heating the Pt to well above its melting point we also allow most of the oxides to boil away<\/span> as they have relatively low boiling point.<\/p>\n

Back to our bit of Platinum \u2013 once it cools down it will separate by itself from the molten quartz bed leaving it intact. If we try to separate it earlier, it will break the quartz layer under it<\/span> \u2013 this will add to the faster wear of the quartz crucible. But this is not really a problem, considering the very low cost of these crucibles.<\/p>\n

\"\"<\/a><\/p>\n

After the Pt bit is separated we do an inspection of the bottom. I noticed that if there is a hollow point in the bottom, which usually means that not all alloying elements burned always and\/or that the heating wasn\u2019t enough to completely melt the Pt which makes it extremely brittle (mentioned earlier). Thus we have to melt it one more time.<\/p>\n

\"\"<\/a><\/p>\n

THE ROLLING MILL<\/strong><\/h2>\n

So we have refined our Platinum and it is time to start making the foil. For this purpose we will need a rolling mill like the one on the picture left. However these are expensive tools and having an access to a workshop I decided to make my own rolling mill as the one on the right.<\/p>\n

\"\" <\/a>\"\"<\/a><\/p>\n

If you decide to make your own rolling mill here are some remarks from my experience working with it.<\/p>\n

As I said the idea for the rolling mills was taken from a picture on the Internet and the design was simplified. The best is if the both rolls are synchronized with a gearbox and the distance is being regulated in such a way that the pressure on both side bearings is equal – however this greatly complicates the design.<\/p>\n

If the both rolls are moving synchronously they tend to “grab” the material much easier. If there is no gear transmission and the torque is applied to only one of the rolls then by increasing the diameter of the rolls we can overcome the problem with them not grabbing the material.<\/p>\n

To make the spacing between the rolls equal I use two sets of cheap feeler gauges purchased from E-bay. Then I tighten the bolts by hand until the upper roll touches the gauges and then I further tighten it by hand – thus ensuring minimal difference between the left and right side.<\/p>\n

Rolling Mill 1<\/strong><\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

In this mill design the upper bearings are sliding in a stadium slot. Initially the pressure was applied directly on the outer shell but this led (not unexpected though) to bearing breakage. To avoid this problem I cut a slot as indicated in the picture and made a steel foot to distribute the force.<\/p>\n

\"\"<\/a><\/p>\n

That worked but it seemed that one 3\/8-16 Grade3 bolt on each side is not sufficient and when I was tightening the bolts to overcome the bearing play and tighten the elastic deformations (when the foil becomes thinner the elastic deformations in the entire construction become important) their thread got slowly damaged. Grade5 bolts started slowly damaging the thread in the plates, however not significantly. The problem now was that the bearing in the stadium slot did not have equal distribution of the load and eventually cracked where it was free without external support.<\/p>\n

The bearings were relatively small and the end of the rolls did not have enough material to machine a hexagon, so I had to make a hexagon sleeve and a key way to transmit the torque from the wrench – but I forgot to leave space for disassembly of the sleeve.<\/p>\n

Another issue was that the upper roll tends to tilt sideways or jump and bump if no material is pressing it up or because of the tension when the material is leaving the rolls.<\/p>\n

The last issue was the material for the rolls. I used mild steel for the plates and the rolls and no heat treatment for the rolls. The hardness of the rolls wasn’t enough and the surface got marked from the platinum (which was unexpected). Eventually after quite a few of test rolling the surface of the rolls got relatively flat and self-forged with no or barely visible damage from the platinum.<\/p>\n

Rolling Mill 2<\/strong><\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

I used 4″x0.625″ cold rolled mild steel for the plates of the new mill. The rolls I made from 1045 steel and hardened them – I used what I had at hand, but if you have higher carbon content steel, it would be better.<\/p>\n

The first change was to put the upper bearings in a bearing box that will slide inside a slot on the plate. So the outer shell of the bearing is protected and can take a lot of pressure. To distribute the load and the tension I used two 3\/8-16 bolts. For each bolt I made a small flat end step in the case to hold the bolts and the bearing case fixed. I placed a spring (found it in Home depot – 1 long spring was cut in 4 pieces) at the bottom of the bearing case to push and hold the roll upwards and to avoid bumping when the material leaves the rolls.<\/p>\n

I also used larger size bearings 47x25x12 which made it possible to simply mill a hexagon at the end of the lower roll instead of using a sleeve.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

I tested the new design by tightening the pressure bolts as much as I could and turning the rolls. They did not break nor got the threads damaged but the bearings inside got damaged from the excessive force. So I guess flat roller bearings would be better but they are so much more expensive that it is not worth it and I will need to adjust the thickness of the side plates to accumulate the extra width. But again, I don’t need that extra force unless I am planning on rolling some tough materials, but then I will need harder surface on the rolls.<\/p>\n

Just as a note if you decide to endeavor making your own rolling mill, you don’t need more than 6-8 mm of distance play between the rolls and you should leave enough space on the lower side of the slots (those for the bearing casings) so that the springs have enough space to tighten when the roll is at its lowest point – otherwise it will be pushing on a completely closed i.e. solid spring.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

ROLLING THE PLATINUM TO FOIL<\/strong><\/h2>\n

Before you start making the foil you should not know that this is a slow process and requires some patience and perseverance thus don\u2019t give up if you don\u2019t get it right from the first or second or \u2026 try.<\/p>\n

The first step is to hammer on an anvil or something suitable our bit of Platinum that we melted to a thick flat pancake. Don\u2019t hurry and try to smash it with one hit \u2013 it\u2019s not good to mill afterwards and you risk losing the Pt if the bit fly away, take your time. \u00a0\u00a0From time to time turn perpendicularly the Pt bit and lightly hammer the narrow side (indicated with arrows)<\/span> until you get a coin-shaped form. This is necessary in order to reduce the shear at the edges later during the mill process. There is no need to flatten the piece too thin, just enough for the rolls to be able to catch it.<\/p>\n

\"\"<\/a><\/p>\n

Once the Pt bit is flat enough we start rolling through the mill. Initially you will need to push the Pt bit with fingers (do that only in manual rolling mills for understandable reasons) so that the rolls can grab it. You have to this until the piece got thin enough so that the rolls can easily grab and hold it. This is the most tedious part.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

It is VERY IMPORTANT that you don\u2019t change direction of the elongation and you do that ONLY ONE TIME!<\/span> If you start changing the direction of elongation the foil will start shearing at the edges towards the center and you will get something like in my early attempts.<\/p>\n

\"\"<\/a><\/p>\n

That means you don\u2019t turn the Pt piece left and right until you have as length the width that you desire. So if you plan to make a 30mm wide foil, you mill in one direction until you have 35-40 mm length and then you turn 1 time 90 degrees and you continue with your former length now as a width.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

From this point on it is important that you don\u2019t lower the thickness more than 5% at the time and you pass the sheet 3-4 times between the rolls before you change the thickness again<\/span>. When you tighten the rolls you should pay attention that you turn them equally.<\/p>\n

If the sheet starts showing shears on the outside don\u2019t get worried, the outer edge has to be trimmed anyway and this is normal as long as you don\u2019t get something like the picture before the last ones.<\/p>\n

When the sheet starts thinning and especially when the foil is thin I start putting oil<\/span> (automobile oil), a lot of oil, over the foil between the passes. This helps to keep the pressure over the foil equal and prevents the foil from slipping between the rolls – I know it doesn\u2019t make sense, but that\u2019s what I observed.<\/p>\n

\"\"<\/a><\/p>\n

Once the foil is still thick when it becomes longer more than 4 times the width I will cut it in two and continue from there. Trying to make long foil (more than 5 times the width) didn\u2019t work for me, it starts warping and tearing in the middle.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a><\/p>\n

During the entire process the platinum gets self-hardened and needs tempering every time you tighten the bolts<\/span>. In some books it is written that pure Platinum does not self-harden but in my experience 99.95% pure platinum bar did. In fact the hardened Pt sheet became and behaved like spring steel.<\/p>\n

Tempering is done with a propane torch, it is cheap and easy to use and the temperature of the flame is not high enough to melt the platinum. You simply heat the platinum sheet\/foil until it is bright red and leave it to cool down.<\/p>\n

Once you have reached the desired thickness you can trim the foil to a rectangular shape and melt the cutouts to make another foil sheets and so on until you have very small amount of Pt left, which is difficult to make in to a rectangular shape.<\/p>\n

The foil sheets on the book page that you see next are made from 5gr Platinum and 0.5gr was left which was rolled only in one direction to make a Platinum strip shown used in the picture after that.<\/p>\n

\"\"\u00a0<\/a>\"\"<\/a>\"\"<\/a>\"\"<\/a><\/p>\n

On another instance when I was making Platinum foil, there was no need to trim the foil to a rectangular shape and I simply left it in the original form.<\/p>\n

MAKING PLATINUM ANODES FROM THE FOIL<\/strong><\/h2>\n

To make usable anodes the making the foil was the first step from the process. Now we have to make the actual anode unless you are planning to use the foil itself as catalyst. So it would be very useful if we can weld the platinum.<\/p>\n

Graphite welding Platinum to Platinum<\/strong><\/p>\n

\"\"<\/a><\/p>\n

Welding Platinum to Platinum is not that difficult at home. All you need is a computer power supply which has high current output on the 5v bus and 0.9mm graphite fill for a pencil. You can use pliers to hold the graphite and connect the positive output to the pliers where the negative end is connected to an aluminum base over which the Platinum foil is pressed down. You use it by making a contact with the graphite over the foil \u2013 at the point of contact, the graphite starts burning and locally reaching high enough temperature to melt through the Pt foil. Thus if you melt through two or more sheets while they are being pressed down, you get a small hole with melted together edges which is enough to transfer sufficient current later for the chemical process.<\/p>\n